Should I look for a tank with a cigarette puff? Choosing an atomizer (tank) for a cigarette puff The best tank for a cigarette puff.

Tanks and clearomizers

Every vaper sooner or later wonders what is the best tank for electronic cigarettes. Let's start with the fact that tanks are a device where the steam mixture is generated into steam.

That is why vape users want to choose the best tanks for their gadgets, due to which they can better organize the vaping process. So, what is the best tank for an electronic cigarette? This is what we will try to deal with you now.

• serviced (RTA);
• serviced drip (RDA);
• genesis.

There is another category of serviceable atomizers - RDTA, drips that you can service yourself. But in this publication we will talk about ordinary tanks. All of these vaporizer options are equipped with coils, which can be either purchased at a vape shop or twisted on your own.

So, what are serviced tanks. As a rule, most of these evaporators have a base on which, in fact, the heating element (our coil with a wick) is placed. Whereas the tank itself with the vapor mixture is located above the base. Depending on the size of the tank, it can hold from 2 to 10 ml of liquid.

Most of these evaporators, released recently, are equipped with top airflow. The principle of operation in this case is as follows: the air first of all descends to the winding outside the chamber, and only after that it goes up through it, that is, to the drip-type.

The bases of serviced tanks are equipped with slots or holes, through which the vaporized liquid rises through the wick to the heating element

Drips, unlike tanks, have a small bath for refilling, respectively, less liquid will interfere with them. Heating coils are also located at the bottom of the evaporator, and the wicks are immersed in the recharge bath.

In addition, the drip does not have a chamber, since the vapor mixture is in any case below the spirals. Instead, the RDAs are equipped with a top cap that sits on top of the base. Air enters through the bottom, top or side vents and rises from the top cap to the drip tip.

Genesis atomizer is a combined evaporator in which a drip and a tank are combined. They have a capacity similar to the RTA, but they are located at the bottom of the atomizer, under the base. Due to this, the effect of having a deep bath is achieved.

A rolled stainless steel mesh acts as a wick, through which the steaming mixture enters the winding. In addition, Genesis, like drips, has a top cap. Yes, and air circulation occurs according to the principle similar to drips.

Tank Advantages

First of all, I would like to note the advantages of serviced tanks over unattended ones - a vape user does not need to purchase factory coils, they can be made with my own hands. This not only allows you to save on winding electronics, but also gives you the widest possibilities when vaping (the larger the winding area, the more steam it produces).

If we compare tanks with drips, then the former have the following advantages:

1. The volume of the contained vapor mixture.
   It's no secret that RDAs are drip-filled, that is, they drip a certain amount onto the winding and soar for 8-10 puffs. The tank is good because, as mentioned above, up to 10 ml of liquid is placed in its tank. This means that you can use the vape between refills almost all day (it all depends on the frequency of vaping).
2. If the vape is not standing vertically, then, in the case of a drip, it may leak.
   Whereas with the tank, the electronics will not leak. This is due to the fact that there is no camera in the drips, but there is one in the tanks.
3. Compared to drips and genesis, tanks are easier to wind.
   At the very least, genesis owners note that they always have to take care of the correct oxidation of the mesh and determine the hot spots where the mesh will come into contact with the heating element.

To make it easier for you to decide which serviced tank to choose, we offer you our top 5 most popular vaporizers for electronic cigarettes.

Pharaoh by Rip Trippers/Digiflavor

The diameter of this tank is 25 mm, and on its base you can install a single or double winding of a wide variety of configurations. The base itself is equipped with two racks with spring clips for fixing coils. The single wick and opening can be closed and opened by the user of the electronics as needed.

This vaporizer model provides the vaper with the widest airflow adjustment options. This is due to the fact that the tank is equipped simultaneously with three central rectangular holes, the size of which is 5 * 2.5 mm. Thanks to this, both a hookah puff and a tight cigarette puff are possible.

For stable use of the TK mode, the positive connection was gold-plated during the manufacturing process. And thanks to the presence of a PEEK insulator, high vaporization is ensured.

Such a tank is perfect for those vapers who are looking for a brand new, interesting and tasty atomizer for their electronics.

Advantages:

• the presence of a multifunctional base opens up a wide range of vaping opportunities for the vaper;
• the possibility of equipping the base with creative windings;
• ease of maintenance, namely in the installation of wicks;
• good taste qualities of the given steam;
• the possibility of a hookah puff, as well as a tight cigarette;
• good steam generation.

As for the shortcomings, there is only one – for some vapers, a 2 ml tank is not enough.

And in all other respects, these tanks are considered one of the most popular atomizers of our time.

Griffin 25mm RTA by GeekVape

An improved vaporizer model from the world famous GeekVape, which appeared before vapers in a new 25mm version. 2 versions were released: with top airflow and no airflow at all.

The base of this tank can still be equipped with one or two coils at the same time, but unlike the old version, now its size is 17 mm.

In this version of the atomizer, the volume of the reservoir is already as much as 6 ml, which is twice as large as the previous Griffin. These vaporizers are suitable for both experienced vapers, and even novice vapers who have just begun to comprehend the intricacies of such a truly fascinating culture as vaping can handle them.

Advantages:

• high-quality veloci-stands with holes for fixing the winding Ø5 mm;
• the possibility of soaring in temperature control mode;
• the presence of a gold-plated 510 type connector and a PEEK insulator ensures a stable connection between the tank and the vape itself;
• a sufficiently large volume of the tank for refueling;
• the ability to use various drip types;
• providing fantastic taste and a decent vapor cloud;
• ease of installation of spirals and wicks.

Of the shortcomings, only that this tank is a bit tall.

Avocado 24 by GeekVape

A modern tank, the diametrical size of which is as much as 24 mm. This evaporator model is equipped with high-quality velocity stands, with which you can securely fix the coils on the base.

The size of the opening for the wicks is 4 mm, which allows even beginners to use such devices. As for the volume of the reservoir, this advanced model includes as much as 5 ml of liquid.

Innovative dual 3mm refill ports with pivoting lid make refilling simple and easy. In addition, Avocado provides the ability to adjust the size of the air duct opening: if they are fully opened, then their size will be 7 * 2 mm. To change the size of the holes, just rotate the top cap.

In addition, the tank is equipped with a ceramic insert that can be installed instead of one of the coils. Thanks to the convenient base and ease of maintenance, the Avocado 24 will appeal to everyone, from a novice vaper to a professional.

Advantages:

• getting a bright taste of steam even with an active one spiral;
• excellent vaporization when using two spirals;
• ideal price / quality ratio;
• wide range of vaping options;
• the possibility of soaring like on a drip;
• due to its small size, this tank will perfectly complement almost any vape;
• Due to the possibility of complete disassembly, this vaporizer can be completely washed after use, which greatly extends its service life.

Flaws:

• this tank may leak if dropped.

Another vaporizer that is very popular among pro vapers. In terms of performance, it has certain similarities with the Geekvape Griffin tank. It is easy to use, has a spacious base that can easily fit two coils.

This tank is mostly designed for aroma transfer, but can also be used for sub-ohm vaping.

Advantages:

• convenient and affordable design;
• simple and spacious base with the ability to install a pair of spirals;
• convenient refueling process - top;
• high rates of vaporization and taste transfer;
• ease of installation and assembly.

Flaws:

• it is not intended for releasing huge clouds of steam, that is, it is better not to take this tank for cloud chasing.

Kayfun v5 by SvoeMesto

The tanks of this manufacturer are valued by their owners for their excellent transmission and wide possibilities for adjusting the vaping process.

Advantages:

• the widest range of airflow adjustment;
• you can buy a tank in stainless steel or glass;
• high quality construction, which leads to a long service life;
• the possibility of equipping the base with large spirals;
• excellent flavoring.

Of the shortcomings, only that there is no hookah puff on this tank.

If you use an electronic cigarette with a tank, then here are a few good advice on the use of such gadgets:

1. In order for the vaping process to be of high quality, you need to make sure that the coil covers the air duct opening, especially in atomizers with a bottom airflow.
2. Coils that are too short will cause liquid that drips onto the wick to enter the blow hole, resulting in gurgling and leaks. To prevent possible vaporizer leaks, you need to make sure that the vapor mixture does not drip freely onto the base past the tails of the wick. The latter should optimally block the holes for the liquid.
3. If the tank starts to vape dry, it means that you have overdone the blockage and prevented the liquid from moving. To balance the vaping process, you need to replenish the tank with filling in a timely manner and monitor the level of liquid in it.
4. Tanks will be the most suitable option for the first vape on serviced vaporizers, since most of these gadgets allow the vaper to reach the base at any time to reinstall the wick.
5. And, lastly, make sure that the container is not overfilled with vaporous liquid. There should be some air left in it, due to which the liquid can evenly soak the tails of the wick. It also causes the timely replacement of the evaporated liquid with air.

Summing up

Tanks are a great alternative to conventional atomizers. They are roomy, tasty and give out a lot of steam. In the case of serviced evaporators, it is easier to wind the bases yourself, and it will be cheaper in terms of money. Maintenance-free tanks after use (which is 6000-8000 puffs) are subject to disposal, and there is no possibility of varying the characteristics of the coils on them.

From the top tanks offered above, you can choose for yourself the device that will definitely be able to satisfy your vaping needs. What vaporizer do you think is the best to use on electronic cigarettes?

Recently, vaping - smoking electronic cigarettes - is at the peak of popularity. Although, according to vapers, smoking is not quite the right term for this process, because in fact, only the inhalation of vapor, or “soaring”, occurs. It is logical that due to the increased interest in electronic cigarettes, the range of vaping accessories began to expand. Let's focus on the most important part of the steam generator - the atomizer, consider its device, the principle of operation and determine the best atomizers for electronic cigarettes.

Today, everyone who has ever tried electronic cigarettes knows more or less about atomizers. This is not surprising: it is this element that allows us to consider an electronic steam generator a cigarette. Of course, the battery pack, with the help of which current is supplied for the timely evaporation of liquid from the tank, is also of no small importance. However, it is the atomizer that can be called the "heart" of the electronic cigarette. The design features of the atomizer provide the main properties of the vape device: the density and volume of the exhaled vapor, the rich taste and aroma of the liquid filled into the device.

If you are new to the world of “vaping” and do not yet understand exactly how an atomizer functions, remember ordinary boiler. It is with this unpretentious device that our device can be compared. The very design of the atomizer is a nichrome spiral, inside of which there is a wick (quartz thread) impregnated with a non-flammable liquid. When voltage is applied to the coil from a source of electricity (battery), it instantly heats up and heats the wick very much. The liquid in the wick also reaches high temperatures and goes into steam. The resulting vapor is inhaled by vapers.

Accordingly, if the liquid is flavored, the vapor also becomes palatable.

Thus, in order for the atomizer to work correctly, the following components of the device are required:

1. A battery that acts as a source of electricity.
2. Refilled liquid (usually a replacement cartridge). It is she who wets the wick inside the spiral.

The smoker is inhaled through a special mouthpiece. With the help of connecting elements, a battery mod and an atomizer, or, as it is called, a tank, form a single electronic device with different characteristics.

Classification of atomizers

The vaping industry is constantly evolving, and manufacturers offer a ton of options for vapers. These devices vary in size, design features, coil resistance, maintenance. In order not to make a mistake in choosing an atom, it is best to know the main features of a particular type.

Service possible

The most common classification of vape devices is serviceability.

1. serviced. These are atomizers, the manufacturer of which makes it possible to manually change the heating element - a nichrome spiral. As a rule, inside the design of such atomizers there are special fasteners for convenient installation of the coil. Some models also allow you to replace the wick yourself and customize the device to your taste (for example, adjust the winding of the spiral). This type of atomizer is suitable for those users who do not want to constantly buy new devices - it is easier to replace the necessary elements in an existing device. Perhaps, for beginners, a serviced atomizer will not seem like the most successful acquisition, but over time, having understood the range of accessories and understanding the principle of operation, they will opt for this particular type. Full service models are found among clearomizers, tankomizers, atomizer drips.
2. Semi-serviced. In this case, changing the coil will not work, but the manufacturer allows you to change the whole evaporator, that is, part of the atomizer with a coil and screwed wicks. In this case, there is no provision for changing the winding of the spiral, which means that it is impossible to adjust the taste and amount of steam generated. The replacement process is quite simple: it will be enough just to attach a new evaporator to replace the old one to the main base of the device. In general, it is even more convenient and takes much less time than painstaking manual installation of the coil into the compartment with fasteners. This type includes the following devices: clearomizers, Ego-C atomizers, DCT tanks.
3. Unattended. These devices are considered disposable. They have a limited service life, because in the event of a malfunction, it will not be possible to change the heating element. After a breakdown, most likely, you will have to purchase a new model. However, disposable atomizers also have their own varieties: with replaceable cartridges (the most short-lived and inferior in taste to other types), more reliable cartomizers in the form of a tube and clearomizers with a large liquid capacity.

According to the degree of resistance of the spiral

As mentioned above, the devices are equipped with a nichrome spiral - the main heating element of the design. The electrical resistance may vary. Ohm's law, known since the school physics course, says that the greater the resistance, the less current is supplied. In our case, the resistance of the coil determines how thick and at what temperature the steam will be.. If the number is low, then the output is very hot and dense steam. The resistance value is affected by the size of the heating coil and the number of turns in it.

1. Standard: The resistance is between 2.1 and 2.6 ohms. Steam is formed of medium density and saturation - this is the most acceptable option for vapers.
2. Low resistance: no more than 2 ohms. These devices generate much more steam than standard models, however, as a result of intensive work, they often fail.
3. high resistance: more than 3 ohms. Vaporization is powerful and rich, the taste of steam is usually bright. Such tanks are equipped with a more capacious and high-quality battery than the rest.

By type of construction

The third and rather important criterion by which atomizers are classified is the type of construction. In fact, it is the design of the device that determines its main qualities.

Top 5 e-cigarette tanks

How to determine best atomizer among the abundance of proven devices and fresh new products? There are several criteria for identifying the best atomizer, but mostly it is the taste and the duration of the puff. There are three types of puffs: hookah, medium and cigarette. If you are purchasing an electronic device for the purpose of quitting smoking, then we advise you to opt for tanks With cigarette puff . The taste of steam is more dependent on the liquid that impregnates the synthetic winterizer. It is better to adjust the brightness of the taste yourself, which means that you should pay attention exclusively to serviced models. Having determined the main requirements for buying a high-quality atomizer, we offer you a small rating of the best models. All of them were released during 2016 and 2017, and in a short time they have proven themselves among experienced vapers only on the positive side.

5th place - Geek Vape Ammit RTA

On the fifth place of the top is a tank with one spiral and 3D airflow. This device was produced in 2016, and since its inception has gained popularity among vapers. The reason for this is the excellent taste of steam thanks to a powerful tank and a versatile, practically 3D blowing inner spiral. Air is supplied from two slots at the top and bottom, and air is also supplied from the side.

Inside the design there are large holes for attaching the coil, so it will not be difficult to replace it even for a novice vaper.

In the delivery set there is an additional fastening-clamp for the correct and reliable installation of the heating element. The liquid supply can be controlled independently thanks to the slots in the tank. The Geek Vape Ammit RTA Tank is easy to refill, just remove the top cap and load e-liquid into one of the slots. The body is made of stainless steel, the tank itself is made of glass. The diameter is 22 mm, the volume of the tank is 3.5 ml.

4th place - Billow v2

This model is a novelty medium puff, serviceable atomizer from the manufacturer Ehpro. This modification means installation of two coils. There is a bottom blowing of the spiral, while the air comes from a pair of holes at the bottom of the base. You can adjust the airflow with a rotary ring. The liquid tank is characterized by a large capacity - the volume is 5 ml.

The body of the tank is made of glass, which means that you can control the level of liquid inside at any time.

The base of the atomizer is equipped with 3 racks with special slots for strong installation of coils. The ends of the helix are held in place by Phillips screws. Refilling this tankomizer is simple: you need to turn it over with the drip tip down and disconnect the base. Next, you will need to fill the liquid through one of the filling holes, and then carefully screw the base back. The disadvantage of Billow v2 compared to similar models is education a small amount of steam- most likely, it will not work to create a huge cloud around you.

3rd place - UD Goblin Mini V3 RTA

This modification was developed by UD Technology. The tank consists of five main parts: the base of the device, a replaceable deck, a dome of the evaporation chamber with an air duct, a body and a top cap - a cover for filling. The tank can function with one or two coils thanks to deck replacement system, and there is a swivel airflow adjustment ring, which can be adjusted to your liking. On the ring, you can see a special engraving, indicating the degree of opening of the air supply hole. There is also a mark by which you can track the amount of liquid in the tank.

The volume of this atomizer is 2 ml of liquid, but you can additionally purchase replaceable tank up to 4 ml. The flask of the tank is glass, and the glass, if necessary, can be replaced with a new one.

All you need to properly fill the tank is to stop pouring liquid into the evaporator and unscrew the top cap. Then you just need to pour new fluid into the tank through one of the holes in the base. The obvious advantage of the UD Goblin Mini V3 RTA is its small size, functionality, ease of operation and excellent dense vapor. The disadvantage lies in the need purchase additional parts, for example, a larger tank.

2nd place - Crius

In the second place of the top is the serviced Crius atomizer with bottom and side airflow. Puff - hookah, free. The first thing that catches your eye when you see the device - rich equipment and a huge selection of spare parts for the limitless imagination of vapers and full control over the steaming process. There is a space in the atomizer box under the main upper compartment in which the manufacturers placed a set of several coils, a piece of wire for self-winding the coil, and a piece of Japanese cotton filler. The manufacturer took care of a set of duplicate swivel rings and tank glasses.

In the tankomizer, convenient control of the liquid supply is carried out: you just need to carefully turn the body of the tank relative to the base. The diameter is 22 ml, the volume of the tank is 4.2 ml. The advantage of Crius is to get thick and voluminous steam in addition, the device is refueled without difficulty - just slide the tank cap and load the liquid into the opened hole.

1st place - Steam Crave Aromamizer RDTA

One of the best tanks of 2017 is the Aromamizer RDTA from Steam Crave. This vape device is equipped with capacious tank about 7 ml. In the latest model, the tank diameter is as much as 25 mm. There is a convenient base with two large posts to simplify the installation of the coil. The spiral is blown here from the side, and it is possible to adjust the air supply to your liking - there is a rotary ring for this.

To fill the tank, you will need to shut off the fluid supply, turn the top cap and pour fluid into the tank. Before unscrewing the tank cap, we recommend that you pay attention to the corresponding mark. The body of the tank is made of high-quality glass (there is also a spare in the delivery set). Thus, the main advantage of this model can be considered convenient refueling, an excellent capacious tank and a pleasant rich taste of the resulting steam.

Conclusion

We hope that our article has helped you better understand what atomizers are, how they work, and which models are considered leaders in the modern vaping industry. We have determined the best atomizer based on user feedback and device characteristics, but do not forget that manufacturers are constantly "upgrading" their developments and offering innovative devices. So, over time, the models will improve and delight vapers with new features and capabilities.

At the moment, there are already a lot of various atomizers, for a free (hookah) puff and for a tight cigarette puff, serviced and unattended, with a container for liquid and without a container for liquid, with a cotton wick on a grid (genesis), in general, for various needs and consumer wishes. We will consider only serviced atomizers and they can be divided into several categories:

RTA - tanks, RDA - drips, RDTA - the so-called "bakodripki"

In this article, we will try to figure out which one to choose. MTL atomizer (tank, drip) for a cigarette puff.

Since a lot of different hardware has already been used and tested, I will rely only on personal experience and your taste. I started using atomizers on cigarette puff about three years ago, at the same time, the boom in the development of the vape industry began and there was no such variety of devices as there is now. The first was Kayfun V 3.1 RTA, then Tayfun RTA, Erlkonigin RTA, Ahilles RTA, Origen V 2 (genesis), Ataman RTA V 2, By-ka V 5 and V 6 RTA , Kayfun V 4 RTA , Kayfun 3 mini RTA , Kayfun V 5 RTA - all these atomizers are sharpened specifically for a tight cigarette puff and have similar design features, namely: a small air supply hole, also a small coil blowing hole, a necessarily serviced base for one coil. Also, on atomizers for a cigarette puff, you must use the correct liquid with a proportion PG/VG - 50/50, but this is not necessary, everyone decides for himself what is right and what is not, but I use just such a proportion and a strength of 3 mg / ml.

In 2017, I can single out a few worthy representatives in the category of "cigarette tanks". I’ll probably give the first place for a real folk tank Merlin mini RTA , for its compact size, ease of use, chic taste transfer, affordable price and versatility, by the way, this tank has been in personal constant use since the day of release, more detailed overview you can watch my video:

Buy Merlin mini RTA in Ukraine can be around $20 per unit.

And Berserker RTA

You can see it in more detail in my video:

I hope this article will help you make a choice. MTL atomizer for a cigarette puff, of course, I did not touch on all the technical points, and if you have any questions, feel free to ask them in the comments, I will answer everyone if possible.

All thick and delicious steam!

There are two main classes of tanks that are mounted on an electronic cigarette power supply, namely clearomizers and atomizers. Everything is quite simple: in the tank of an electronic cigarette there is a chamber for evaporating liquid, where a spiral serves as a heating element, there may be one or two, in rare cases three or more. So here are the differences between clearomizers (Clear Atomiser) and atomizers (Rebuildable Atomizer) are whether the evaporation chamber at the tank is replaceable, or whether it is serviced. The replaceable evaporation chamber is called an evaporator.

Replaceable evaporators come in a variety of types and types, they also have a different number of coils, different materials for absorbing liquid and supplying it to the coil, which will heat up when tightened, turning the liquid into vapor.

There are various recommendations for maintaining the evaporation chamber, they are intended for advanced users who already know how to make spirals themselves, how many turns to make, and what material the spiral will be made of. There are different approaches to winding certain models of atomizers due to the design features.

There is a wide range of materials used as an impregnated wick, usually through a helix. As wicks, silica, cotton wool of Japanese origin, which has directional fibers, can be used in order to make it easier to thread the wick into a spiral. There are also exotic materials such as linen wadding and many others. Each material conveys the taste of the liquid in its own way. Moreover, different types of spirals and materials from which the wire is made also affect the taste sensations and give different resistance.

Atomizers are also divided into types according to the tightening force. Two classes can be noted: cigarette puff and hookah.

Atomizers with a cigarette puff give relatively no a large number of vapor, as a rule, have a good taste transfer, you can also note a somewhat tight puff, unlike hookah tanks, which imitate a puff on an analog cigarette. Cigarette atomizers include tanks such as Taifun and Kaifun. Most atomizers have an airflow control that adjusts how tight the puff will be. However, on a cigarette atomizer, the puff will still remain rather tight, and on a hookah tank, it will be quite loose, due to the design features of the shaft and airflow.

Clearomizers, as we agreed, are not serviced tanks, they also have a puff division into cigarette and hookah. Unless there are no difficulties with winding the heating element. In the "clerics" it simply unscrews, or is pulled out of the rubber grooves, when it has served its time and simply changes to a new one.

Currently, manufacturers are actively producing and developing new type atomizers - clearomizers with the ability to install a serviceable vapor chamber (RBA base), also called "hybrid atomizers" in the vape community. Such clearomizers are often included in kits for novice users who want to purchase a device that allows them to immediately evaluate the entire spectrum of vaping sensations. These clearomizers are Kangertech SubTank (nano, plus, mini), Joytech Delta ll, Smoktech TFV4 and others.

Summary:

Atomizers (Rebuildable Atomizer) are tanks for advanced fans of electronic cigarettes, because these people are interested in experimenting, and the wider the field for experiments, the better. Therefore, there are a large number of different tanks that provide different taste sensations.

Clearomizers (Clear Atomiser) - tanks with replaceable evaporators. Evaporators are usually easy to change after their working cycle. Vaporizer operation cycle depends on the evaporator model, other factors such as the power supplied from the battery to the evaporator, the frequency of E.C. and even the concentration of certain ingredients of the liquid and its color. On average, the service life is about two weeks.

Hybrid atomizers (RBA base) - tanks with the ability to install a serviceable vapor chamber - an excellent choice for a beginner who wants to get the experience of self-service atomizer, always being able to simply install a ready-made coil and enjoy the taste of vapor. Such devices are now few and often expensive. However, the lineup is constantly being updated and some hybrid clearomizers are not much inferior in scope for winding experiments to traditional atomizers (Rebuildable Atomizer).

There are two types of puff - hookah (also called Californian) or cigarette, which, as its name implies, is similar to the cravings of familiar cigarettes. The vast majority of tanks have a free hookah puff. It gives a large amount of steam and depends on how well the airflow is organized, when the holes are wide, a lot of air enters the spiral through them and it passes freely. At the exit, a free California puff produces a lot of vapor.

The situation with cigarette puffs is different. Cigarette draft is not at all free, but rather tight. To carry out a cigarette puff, you need a well-thought-out airflow - the holes must be covered strongly enough so that air can be drawn in with difficulty, which ensures “tightness”. Since there will be less air on the coil than with a hookah puff, therefore, at the outlet, the tank with cigarette draft will produce less steam.

The vaping culture welcomes big piles and steep clouds of vapor, which is why most tanks are designed specifically for California free draft. While most beginners, in an effort to replace cigarettes, are looking for tanks with a tight cigarette puff. that have a California craving.

Best Cigarette Puff Tanks

Tilemahos V2 by Imeo

Convenient tank with top filling, 4 ml capacity, equipped with frosted glass. The tank has two-way airflow, it has the ability to change the base, where you can install the coil without much difficulty. The tank is very well built, and the original unit is unlikely to experience anything like broken threads, loose o-rings, or fluid leaks. It works well both on open holes for blowing the coil, and on closed holes for getting a tight cigarette puff.

Pico RTA by Promist Vapor

One of the most popular tight draw tanks. The tank itself is quite small, as the name suggests: pico (abbreviated from Italian "piccolo" - small). This tank is only 30 mm high. The tank conveys the taste very well, is equipped with a convenient top filling, has replaceable evaporation chambers, several types of airflow. Here, it is the tight puff that is well implemented, but with the Californian, everything is somewhat more complicated. The tank is designed specifically for a weak amount of steam, and not for a large bulk.
Merlin Mini RTA by Augvape

Easy-to-use top fill tank with 2.5 ml e-liquid capacity. It has the ability to change the bases: one base is designed for two coils for a Californian puff, and the other for one coil for a tight cigarette. At the same time, the airflow of this tank is very wide, air can be supplied to both two and one spiral. The tank is considered universal, since it has two different airflows, it is designed to produce huge clouds of steam, more precisely, for a Californian open draft, and for a tight cigarette puff. It conveys flavor very well and can work well with wide fat coils.

Caiman V4 RDA by Flexoprint

One of the rare types of drips, working under a tight cigarette puff. The drip, compared to its other counterparts, looks quite large and looks like a tank. The reason is that it is equipped with a liquid overflow protection system, or rather, it has a special metal flask inside the device, it also includes several interchangeable plugs (sleeves) for adjusting the airflow (1.7, 2.3, 3.2 mm) . Dripka has a volume of 2.5 mm and is equipped with a fairly deep bath. Dripka is considered one of the best because it is universal, can be used for different types puffs, perfectly conveys taste, you can take it with you everywhere without fear of leaks or overflows.

Kayfun V3, V4, V5

One of the most popular devices among vapers, about which almost everything possible has been said. This is a device that is magnificent in its design features, in which all parts fit together with perfect accuracy. It is extremely reliable, eliminates leaks, squeaks and backlash. All Kayfun devices are perfect for cigarette puff. an almost perfect device in its characteristics, but it requires very fine tuning, unlike the V3 and V5, which are quite suitable for a beginner.

By-ka V6 V7 and others from Vape Systems

By-ka is a very popular device primarily used as a taut cigarette tank. Almost any a new version by-ka will always have the main characteristic - the presence of a tight puff. By-ka is praised for having a very generous package, which includes not only additional glasses, metal flasks and o-rings, but also evaporation shafts, drip tips and tightening sleeves. In other words, a vaper can literally assemble his own device on his own. By-ka is very versatile, it can both pour abundantly and give a modest "cigarette" amount of vapor.