Differences of tanks for electronic cigarettes. Electronic Cigarettes with Cigarette Puff Compact Atomizer for Cigarette Draw
There are two types of puff - hookah (also called Californian) or cigarette, which, as its name implies, is similar to the cravings of familiar cigarettes. The vast majority of tanks have a free hookah puff. She gives a large number of steam and depends on how well the airflow is organized, when the holes are wide, a lot of air enters the spiral through them and it passes freely. At the exit, a free California puff produces a lot of vapor.
The situation with cigarette puffs is different. Cigarette draft is not at all free, but rather tight. To carry out a cigarette puff, you need a well-thought-out airflow - the holes must be covered strongly enough so that air can be drawn in with difficulty, which ensures “tightness”. Since there will be less air on the coil than with a hookah puff, therefore, at the outlet, the tank with cigarette draft will produce less steam.
The vaping culture welcomes big piles and steep clouds of vapor, which is why most tanks are designed specifically for California free draft. While most beginners, in an effort to replace cigarettes, are looking for tanks with a tight cigarette puff. that have a California craving.
Best Cigarette Puff Tanks
Tilemahos V2 by Imeo
Convenient tank with top filling, 4 ml capacity, equipped with frosted glass. The tank has two-way airflow, it has the ability to change the base, where you can install the coil without much difficulty. The tank is very well built, and the original unit is unlikely to experience anything like broken threads, loose o-rings, or fluid leaks. It works well both on open holes for blowing the coil, and on closed holes for getting a tight cigarette puff.
Pico RTA by Promist Vapor
One of the most popular tight draw tanks. The tank itself is quite small, as the name suggests: pico (abbreviated from Italian "piccolo" - small). This tank is only 30 mm high. The tank conveys the taste very well, is equipped with a convenient top filling, has replaceable evaporation chambers, several types of airflow. Here, it is the tight puff that is well implemented, but with the Californian, everything is somewhat more complicated. The tank is designed specifically for a weak amount of steam, and not for a large bulk.
Merlin Mini RTA by Augvape
Easy-to-use top fill tank with 2.5 ml e-liquid capacity. It has the ability to change the bases: one base is designed for two coils for a Californian puff, and the other for one coil for a tight cigarette. At the same time, the airflow of this tank is very wide, air can be supplied to both two and one spiral. The tank is considered universal, since it has two different airflows, it is designed to produce huge clouds of steam, more precisely, for a Californian open draft, and for a tight cigarette puff. It conveys flavor very well and can work well with wide fat coils.
Caiman V4 RDA by Flexoprint
One of the rare types of drips, working under a tight cigarette puff. The drip, compared to its other counterparts, looks quite large and looks like a tank. The reason is that it is equipped with a liquid overflow protection system, or rather, it has a special metal flask inside the device, it also includes several interchangeable plugs (sleeves) for adjusting the airflow (1.7, 2.3, 3.2 mm) . Dripka has a volume of 2.5 mm and is equipped with a fairly deep bath. Dripka is considered one of the best because it is universal, can be used for different types puffs, perfectly conveys taste, you can take it with you everywhere without fear of leaks or overflows.
Kayfun V3, V4, V5
One of the most popular devices among vapers, about which almost everything possible has been said. This is a device that is magnificent in its design features, in which all parts fit together with perfect accuracy. It is extremely reliable, eliminates leaks, squeaks and backlash. All Kayfun devices are perfect for cigarette puff. an almost perfect device in its characteristics, but it requires very fine tuning, unlike the V3 and V5, which are quite suitable for a beginner.
By-ka V6 V7 and others from Vape Systems
By-ka is a very popular device primarily used as a taut cigarette tank. Almost any a new version by-ka will always have the main characteristic - the presence of a tight puff. By-ka is praised for having a very generous package, which includes not only additional glasses, metal flasks and o-rings, but also evaporation shafts, drip tips and tightening sleeves. In other words, a vaper can literally assemble his own device on his own. By-ka is very versatile, it can both pour abundantly and give a modest "cigarette" amount of vapor.
The atomizer is the "heart" of the electronic cigarette. In its design, it resembles a boiler. Inside the tank there is a metal spiral to which liquid is supplied. With the help of electric current from the battery, the vape heats the coil, and the liquid turns into vapor. Tanks with a cigarette puff are equipped with a special blowing system.
Atomizers differ in the type of design:
- Classic. Consist of an evaporator and a replaceable cartridge. They have a simple design and stylish appearance. The disadvantages of such tanks include the formation of plaque on the spiral.
- Cartomizers. The evaporator and cartridge are mounted in one common cylinder. The tank is filled with a special syringe. They give a large amount of thick vapor, which conveys the taste of the liquid well. The devices are disposable. If one of the elements fails, the entire cartomizer is replaced.
- Clearomizer. Tanks made of plastic and glass. The transparent case of such an atomizer allows you to monitor the liquid level. Fully serviced devices.
Most devices with a cigarette type of puff use clearomizers.
Hello, lovers of delicious and thick steam!
Although I left your ranks, I do not lose hope of returning.Long description of the problem:
I started with the cheapest one, bought out of curiosity. And (I didn’t expect it myself!) On the second day I didn’t want to smoke cigarettes at all. The liquids were all delicious, especially the tobacco. There was enough of a couple, I liked everything, and returning to analogue seemed absurd. The euphoria lasted for about a month.
And then the scribe came. The manufacturer closed and my torment began in search of a normal evaporator and tasty liquid. I tried clears with replaceable and non-replaceable evaporators, even rewound these microcoils myself - but happiness did not want to return. These hellish cones flowed, squelched, whistled, did not stretch at all and gave gariki. The desire to smoke added boiling water to the problem. And I bought an Evik mini with a subtank.
The first two days I choked on steam and coughed, none of the old liquid came up. It turned out that the problem was nicotine - it had to be removed completely. But I survived this too, mastered self-mixing, stopped coughing, even got hold of a drip in the pursuit of taste.
And then another scribe came. The taste of liquids ceased to please. He didn't disappear completely, but became nasty. It gave off either metal, or old butter, or soy chocolate, or even hand cream. I steamed a clean base, didn’t steam anything at all, washed the tank, changed the base for kneading and flavoring - the cactus remained a cactus. As a result, I went to a vape exhibition, tried a bunch of liquids, vaped on other devices and made sure that life is pain and everything is not happy.
I abandoned this masochism and returned to regular cigarettes. But health is a pity. I smoked for six months and now I want to try again to switch to steam. And I decided to go the other way - leave nicotine at least 2-3 mg and reduce the power of soaring and the amount of steam (so as not to cough). In short, try to reproduce my favorite ego.
Questions:
I understand that under this scenario I need a tank with a cigarette puff?
Or (well, what if) normal, cigarette and problem-free little ones appeared during this time?
Maybe someone also lost the joy of soaring or returned from the analogue for the second time - what helped you?Buck I looked after Kayfun mini v3 (clone).
What diameter wire to take under a small base? I would like the winding to be 2-2.5 ohms, as it was on his little one.
Does thermal control make sense with such winding or will it not burn anyway? What is better to wind on it - steel, nichrome, titanium or ordinary kanthal?Now I put my Tetris ass in the subtank. The craving changed noticeably, the taste somehow, but returned (especially the tobacco was awesomely brewed for six months). And I'm in doubt - do I need this kayfun? How significantly will it differ from a subtank with a plug? Will there be less vapor and more flavor with it?
I really hope for your help.
Recently, vaping - smoking electronic cigarettes - is at the peak of popularity. Although, according to vapers, smoking is not quite the right term for this process, because in fact, only the inhalation of vapor, or “soaring”, occurs. It is logical that due to the increased interest in electronic cigarettes, the range of vaping accessories began to expand. Let's focus on the most important part of the steam generator - the atomizer, consider its device, the principle of operation and determine the best atomizers for electronic cigarettes.
Today, everyone who has ever tried electronic cigarettes knows more or less about atomizers. This is not surprising: it is this element that allows us to consider an electronic steam generator a cigarette. Of course, the battery pack, with the help of which current is supplied for the timely evaporation of liquid from the tank, is also of no small importance. However, it is the atomizer that can be called the "heart" of the electronic cigarette. The design features of the atomizer provide the main properties of the vape device: the density and volume of the exhaled vapor, the rich taste and aroma of the liquid filled into the device.
If you are new to the world of “vaping” and do not yet understand exactly how an atomizer functions, remember ordinary boiler. It is with this unpretentious device that our device can be compared. The very design of the atomizer is a nichrome spiral, inside of which there is a wick (quartz thread) impregnated with a non-flammable liquid. When voltage is applied to the coil from a source of electricity (battery), it instantly heats up and heats the wick very much. The liquid in the wick also reaches high temperatures and goes into steam. The resulting vapor is inhaled by vapers.
Accordingly, if the liquid is flavored, the vapor also becomes palatable.
Thus, in order for the atomizer to work correctly, the following components of the device are required:
- A battery that acts as a source of electricity.
- Refilled liquid (usually a replacement cartridge). It is she who wets the wick inside the spiral.
The smoker is inhaled through a special mouthpiece. With the help of connecting elements, a battery mod and an atomizer, or, as it is called, a tank, form a single electronic device with different characteristics.
Classification of atomizers
The vaping industry is constantly evolving, and manufacturers offer a ton of options for vapers. These devices vary in size, design features, coil resistance, maintenance. In order not to make a mistake in choosing an atom, it is best to know the main features of a particular type.
Service possible
The most common classification of vape devices is serviceability.
- serviced. These are atomizers, the manufacturer of which makes it possible to manually change the heating element - a nichrome spiral. As a rule, inside the design of such atomizers there are special fasteners for convenient installation of the coil. Some models also allow you to replace the wick yourself and customize the device to your taste (for example, adjust the winding of the spiral). This type of atomizer is suitable for those users who do not want to constantly buy new devices - it is easier to replace the necessary elements in an existing device. Perhaps, for beginners, a serviced atomizer will not seem like the most successful acquisition, but over time, having understood the range of accessories and understanding the principle of operation, they will opt for this particular type. Full service models are found among clearomizers, tankomizers, atomizer drips.
- Semi-serviced. In this case, changing the coil will not work, but the manufacturer allows you to change the whole evaporator, that is, part of the atomizer with a coil and screwed wicks. In this case, there is no provision for changing the winding of the spiral, which means that it is impossible to adjust the taste and amount of steam generated. The replacement process is quite simple: it will be enough just to attach a new evaporator to replace the old one to the main base of the device. In general, it is even more convenient and takes much less time than painstaking manual installation of the coil into the compartment with fasteners. This type includes the following devices: clearomizers, Ego-C atomizers, DCT tanks.
- Unattended. These devices are considered disposable. They have a limited service life, because in the event of a malfunction, it will not be possible to change the heating element. After a breakdown, most likely, you will have to purchase a new model. However, disposable atomizers also have their own varieties: with replaceable cartridges (the most short-lived and inferior in taste to other types), more reliable cartomizers in the form of a tube and clearomizers with a large liquid capacity.
According to the degree of resistance of the spiral
As mentioned above, the devices are equipped with a nichrome spiral - the main heating element of the design. The electrical resistance may vary. Ohm's law, known since the school physics course, says that the greater the resistance, the less current is supplied. In our case, the resistance of the coil determines how thick and at what temperature the steam will be.. If the number is low, then the output is very hot and dense steam. The resistance value is affected by the size of the heating coil and the number of turns in it.
- Standard: The resistance is between 2.1 and 2.6 ohms. Steam is formed of medium density and saturation - this is the most acceptable option for vapers.
- Low resistance: no more than 2 ohms. These devices generate much more steam than standard models, however, as a result of intensive work, they often fail.
- high resistance: more than 3 ohms. Vaporization is powerful and rich, the taste of steam is usually bright. Such tanks are equipped with a more capacious and high-quality battery than the rest.
By type of construction
The third and rather important criterion by which atomizers are classified is the type of construction. In fact, it is the design of the device that determines its main qualities.
![](https://i2.wp.com/tehnika.expert/wp-content/uploads/2017/07/505032_scale_450x450.jpg)
Top 5 e-cigarette tanks
How to determine best atomizer among the abundance of proven devices and fresh new products? There are several criteria for identifying the best atomizer, but mostly it is the taste and the duration of the puff. There are three types of puffs: hookah, medium and cigarette. If you are purchasing an electronic device for the purpose of quitting smoking, then we advise you to opt for tanks with a cigarette puff. The taste of steam is more dependent on the liquid that impregnates the synthetic winterizer. It is better to adjust the brightness of the taste yourself, which means that you should pay attention exclusively to serviced models. Having determined the main requirements for buying a high-quality atomizer, we offer you a small rating of the best models. All of them were released during 2016 and 2017, and in a short time they have proven themselves among experienced vapers only on the positive side.
5th place - Geek Vape Ammit RTA
On the fifth place of the top is a tank with one spiral and 3D airflow. This device was produced in 2016, and since its inception has gained popularity among vapers. The reason for this is the excellent taste of steam thanks to a powerful tank and a versatile, practically 3D blowing inner spiral. Air is supplied from two slots at the top and bottom, and air is also supplied from the side.
Inside the design there are large holes for attaching the coil, so it will not be difficult to replace it even for a novice vaper.
In the delivery set there is an additional fastening-clamp for the correct and reliable installation of the heating element. The liquid supply can be controlled independently thanks to the slots in the tank. The Geek Vape Ammit RTA Tank is easy to refill, just remove the top cap and load e-liquid into one of the slots. The body is made of stainless steel, the tank itself is made of glass. The diameter is 22 mm, the volume of the tank is 3.5 ml.
4th place - Billow v2
This model is a novelty medium puff, serviceable atomizer from the manufacturer Ehpro. This modification means installation of two coils. There is a bottom blowing of the spiral, while the air comes from a pair of holes at the bottom of the base. You can adjust the airflow with a rotary ring. The liquid tank is characterized by a large capacity - the volume is 5 ml.
The body of the tank is made of glass, which means that you can control the level of liquid inside at any time.
The base of the atomizer is equipped with 3 racks with special slots for strong installation of coils. The ends of the helix are held in place by Phillips screws. Refilling this tankomizer is simple: you need to turn it over with the drip tip down and disconnect the base. Next, you will need to fill the liquid through one of the filling holes, and then carefully screw the base back. The disadvantage of Billow v2 compared to similar models is education a small amount of steam- most likely, it will not work to create a huge cloud around you.
3rd place - UD Goblin Mini V3 RTA
This modification was developed by UD Technology. The tank consists of five main parts: the base of the device, a replaceable deck, a dome of the evaporation chamber with an air duct, a body and a top cap - a cover for filling. The tank can function with one or two coils thanks to deck replacement system, and there is a swivel airflow adjustment ring, which can be adjusted to your liking. On the ring, you can see a special engraving, indicating the degree of opening of the air supply hole. There is also a mark by which you can track the amount of liquid in the tank.
The volume of this atomizer is 2 ml of liquid, however, you can additionally purchase a replaceable tank up to 4 ml. The flask of the tank is glass, and the glass, if necessary, can be replaced with a new one.
All you need to properly fill the tank is to stop pouring liquid into the evaporator and unscrew the top cap. Then you just need to pour new fluid into the tank through one of the holes in the base. The obvious advantage of the UD Goblin Mini V3 RTA is its small size, functionality, ease of operation and excellent dense vapor. The disadvantage lies in the need purchase additional parts, for example, a larger tank.
2nd place - Crius
In the second place of the top is the serviced Crius atomizer with bottom and side airflow. Puff - hookah, free. The first thing that catches your eye when you see the device - rich equipment and a huge selection of spare parts for the limitless imagination of vapers and full control over the steaming process. There is a space in the atomizer box under the main upper compartment in which the manufacturers placed a set of several coils, a piece of wire for self-winding the coil, and a piece of Japanese cotton filler. The manufacturer took care of a set of duplicate swivel rings and tank glasses.
In the tankomizer, convenient control of the liquid supply is carried out: you just need to carefully turn the body of the tank relative to the base. The diameter is 22 ml, the volume of the tank is 4.2 ml. The advantage of Crius is to get thick and voluminous steam in addition, the device is refueled without difficulty - just slide the tank cap and load the liquid into the opened hole.
1st place - Steam Crave Aromamizer RDTA
One of the best tanks of 2017 is the Aromamizer RDTA from Steam Crave. This vape device is equipped with capacious tank about 7 ml. In the latest model, the tank diameter is as much as 25 mm. There is a convenient base with two large posts to simplify the installation of the spiral. The spiral is blown here from the side, and it is possible to adjust the air supply to your liking - there is a rotary ring for this.
To fill the tank, you will need to shut off the fluid supply, turn the top cap and pour fluid into the tank. Before unscrewing the tank cap, we recommend that you pay attention to the corresponding mark. The body of the tank is made of high-quality glass (there is also a spare in the delivery set). Thus, the main advantage of this model can be considered convenient refueling, an excellent capacious tank and a pleasant rich taste of the resulting steam.
Conclusion
We hope that our article has helped you better understand what atomizers are, how they work, and which models are considered leaders in the modern vaping industry. We have determined the best atomizer based on user feedback and device characteristics, but do not forget that manufacturers are constantly "upgrading" their developments and offering innovative devices. So, over time, the models will improve and delight vapers with new features and capabilities.
At the moment, there are already a lot of various atomizers, for a free (hookah) puff and for a tight cigarette puff, serviced and unattended, with a container for liquid and without a container for liquid, with a cotton wick on a grid (genesis), in general, for various needs and consumer wishes. We will consider only serviced atomizers and they can be divided into several categories:
RTA - tanks, RDA - drips, RDTA - the so-called "bakodripki"
In this article, we will try to figure out which one to choose. MTL atomizer (tank, drip) for a cigarette puff.
Since a lot of different hardware has already been used and tested, I will rely only on personal experience and your taste. I started using atomizers on cigarette puff about three years ago, at the same time, the boom in the development of the vape industry began and there was no such variety of devices as there is now. The first was Kayfun V 3.1 RTA, then Tayfun RTA, Erlkonigin RTA, Ahilles RTA, Origen V 2 (genesis), Ataman RTA V 2, By-ka V 5 and V 6 RTA , Kayfun V 4 RTA , Kayfun 3 mini RTA , Kayfun V 5 RTA - all these atomizers are sharpened specifically for a tight cigarette puff and have similar design features, namely: a small air supply hole, also a small coil blowing hole, a necessarily serviced base for one coil. Also, on atomizers for a cigarette puff, you must use the correct liquid with a proportion PG/VG - 50/50, but this is not necessary, everyone decides for himself what is right and what is not, but I use just such a proportion and a strength of 3 mg / ml.
In 2017, I can single out a few worthy representatives in the category of "cigarette tanks". I’ll probably give the first place for a real folk tank Merlin mini RTA , for its compact size, ease of use, chic taste transfer, affordable price and versatility, by the way, this tank has been in personal constant use since the day of release, more detailed overview you can watch my video:
Buy Merlin mini RTA in Ukraine can be around $20 per unit.
And Berserker RTA
You can see it in more detail in my video:
You can also add Kayfun V5 and V5 mini to this list, but there are a couple of points. The first is the price of the original 150 euros, buy a clone
Kayfun V5 in Ukraine will not be difficult at a much affordable price around $ 20, the second is the need to "dope" the airflow hole of the spiral, in order to achieve a really tight tightening, you will need to find a special bushing.If you choose any of these atomizers, you are guaranteed to be satisfied with the result, everything is decided by the thickness of your wallet and the superiority of a hamster over a toad :-) All three worthy representatives MTL categories with their individual features and benefits.
Buy Berserker RTA in Ukraine it is possible within 1000-1200 UAH, and in China the price tag for it will be quite democratic in the region of $ 30, but to buy By-ka V 7 RTA in Ukraine it is already possible, but the price around $ 150 is exorbitant in my opinion, so it’s worth waiting for the appearance of clones in Chinese stores, sometimes they are of very decent quality, no worse, and in some places even better than the original.
Time does not stand still and everything changes, the leaders in this segment too, you can see a detailed comparison and definition of which tank to choose in my video:
I hope this article will help you make a choice. MTL atomizer for a cigarette puff, of course, I did not touch on all the technical points, and if you have any questions, feel free to ask them in the comments, I will answer everyone if possible.
All thick and delicious steam!