How to open a beeline tablet. How to open tablet

Most modern tablets look solid and misleading that they cannot be taken apart or opened to the average user. However, this is not the case. If you look closely, then on each device you will find the lines of joints and will be able to independently cope with its opening. To make it easier for you, we offer instructions on how to remove the back cover of the tablet.

Before starting work, think carefully about whether it is worth doing. Removing the cover is not tricky, but doing it carefully, without damaging a single part, and leaving the equipment in working condition is much more difficult. Moreover, the same common cause opening the rear panel - replacing the battery. We hasten to upset you that in most models it is soldered to the motherboard. Therefore, if you do not have a discharge for accurate soldering, then it is better to leave this matter to professionals.

For work you will need the following inventory:

screwdrivers various forms and sizes;
a regular plastic card or pick for a guitar.

Cover removal instructions

To begin with, carefully inspect the cover for the presence of various clamps or screws (they may be under rubber plugs).
If any are found, carefully unscrew or open them. Place all removed screws in separate containers, making a short note for yourself about where they were.
Pry the tablet cover very gently with a pick or a plastic card. They need to be inserted to a depth of about 5 mm, and then smoothly drawn along the entire perimeter.
After that, carefully lift the cover, making sure that no cables or elements are glued to it.

Try not to open your tablet frequently. Already after 2-3 openings, some of the latches and latches may not withstand and break, which will lead to the formation of a gap into which dust and other contaminants will regularly enter.

To open the back cover on a Lenovo tablet, you will have to use ingenuity, because. each model has its own design features. Below will be described general recommendations, we will also look at the process of removing the cover using the example of the A3300 model.

In order to open the tablet and remove the back cover, you must first carefully examine the device from behind. On some models, to open the cover, you will need to unscrew a few bolts. However, often the cover is removed very simply - you just need to pry the cover along the frame with a thin screwdriver.

Lenovo A3300

Opening the lid of this tablet is not too difficult, but extreme care must be taken as it may be damaged.

Take a flat (not curly) screwdriver and stick it into the USB output and gently push towards the cover.
After a characteristic click, you need to drive the screwdriver in reverse side from the power button and volume rocker.
We lead a screwdriver to the middle of the side and you can remove the cover.

It is best to find a video guide for your tablet model on the Internet in order to more clearly see the process of opening the device. Below is a video that tells about the disassembly of the Lenovo S6000 tablet.

Quite often, tablet owners need to open the back cover - clean the volume buttons or replace components. It is for solving such problems that this article will come in handy, in which we will figure out how to open the tablet cover on our own.

The disassembly process does not differ much, and in some cases does not differ at all. Therefore, we will consider the general algorithm of actions and pay attention to some of the nuances.

Preliminary preparation

Before you begin, you must turn off the tablet and remove all SIM cards and USB drives from it. If this is not done, the cover may not be removed or the cards or attachments may be broken. - we will climb inside the device and excess dust, and even more dirt, we do not need it there.

We will need screwdrivers (most likely Phillips) and a plastic card (which is not a pity).

Parsing the algorithm

In the most general case, we simply find a place where we can insert a plastic card. Usually this place is near the volume buttons. We need to carefully, prying off the edge, disconnect the front and back of the tablet, splitting the fasteners. Sometimes a pick can be used instead of a card.

With this method of opening the case, nothing will be damaged, feel free to move the card along the case and the latches will open

But you need to be very careful - in many models, manufacturers love to hide bolt fasteners. Before starting work, be sure to make sure that there are none. You need to apply moderate force. If the latch does not give in in any way, check additionally if there are any fasteners in this place. Sometimes they can be disguised as stickers or under places that mimic part of the touchpad.

It doesn't matter which manufacturer your tablet is from - Asus, Samsung, Lenovo or Prestigio - in all cases, the algorithm of actions will be the same.

After you managed to walk around the entire perimeter, do not rush to pull back the lid. First make sure that there are no cables going to it, if there are any - disconnect them if necessary.

The tablet is open, and we can start the work we need - replacing the battery or any other parts, cleaning the device from dust.

Conclusion

Very often, an ordinary user is simply afraid to touch the hardware, which is correct in many cases, but not always. How to open the back cover of the tablet - we figured it out, there is nothing complicated about it. The main thing is to be careful and act very carefully so as not to damage the filling. Basically, the lid is opened to

In modern tablets, it is difficult to find visible screws or bolts, so the user who decides to disassemble the tablet often falls into a stupor, but how to disassemble it?

Usually, the back cover of the tablet is held on by latches located around the perimeter. To open it, there should be a place on the lid where you can slip a thin flat object, preferably a plastic one, to start snapping it off. Often, this notch is located next to the volume buttons, or next to the power button.

How to disassemble the Galaxy Tab 2 tablet

The man in the video shows how to disassemble the Galaxy Tab 2 to clean the sticky buttons.

How to disassemble the tablet completely

In the previous video, the person only removed the back cover. But what if you want to disassemble the tablet completely?

And how to disassemble a Chinese tablet?

There are no screws, no bolts, no slots to pry the back cover. But in fact, everything is quite simple:

And another option, cheaper than the previous one:

So that you don’t have to look for “how to assemble a tablet” later, and you are not sure that you will remember how and in what sequence you disassembled it, it’s better to immediately entrust it to specialists.

If you need to open the tablet lid, read our article. We will tell you whether it is possible to remove the back cover yourself and how to protect yourself during work.

How to open the tablet cover?

Many tablets outwardly give the impression of solidity. No latches or screws are visible, just various connectors and buttons. It is clear that this is a deceptive impression, but, nevertheless, it is not easy to figure out on your own how to open the tablet lid. Check out our recommendations and you will be able to do it.

Opening the lid

Opening the back cover of any tablet is not very easy, so let's try to figure out the basic steps. If you are the owner of a rare model, it is better to read the relevant recommendations on the specialized forums or seek help from a specialist.

Digma Optima 10.5 3G touchscreen replacement

In this video ras…

How to disassemble tablet Digma Plane 7.8 3G PS7008EG

In this video we will show you how to disassemble Digma tablet Plane 7.8 3G. You will learn what you need to pay attention to when parsing.

For work you will need:

a set of screwdrivers, including straight, cross-shaped, three- and hex;
guitar pick or plastic card;
hot air gun

Progress

First of all, take a good look at the tablet. Before removing the back cover, for many models it is necessary to unscrew the screws or snap off the latches. You will most likely notice the latches, but the screws can be hidden under the rubber plugs. If you see these, carefully pry them up and check for screws under them.
Screws found. Select the appropriate screwdriver from your set and unscrew them. If there are latches, snap them off.
Now the hard work begins. Slowly pry off the tablet cover with a pick or a plastic card. This must be done with extreme care so as not to damage the fragile components of the equipment. In most cases, the work of removing the back panel ends here. But there are models that are difficult to open.

Difficulties in removing the cover

Devices that are difficult to open include Apple products. Tablets of this type are very difficult to disassemble, so think carefully before doing this. For some models, for additional fixation and protection against non-service maintenance, the back panel is glued. This is where the hot air gun comes in handy.